TumblrFeed

Where Every Scroll is a New Adventure

3d Printing - Blog Posts

4 months ago
My Daughter And I Successfully Sent And Received Test Texts To One Another Once Everything Was Setup.

My daughter and I successfully sent and received test texts to one another once everything was setup.


Tags
4 months ago
If You Are Going To Use A GPS With Your Unit You Will Need To Enable The GPS Mode And Then Set The Rx

If you are going to use a GPS with your unit you will need to enable the GPS mode and then set the rx and tx pins that you have soldered to on the circuit board of the radio. Here they're set to 48 and 47, respectively.


Tags
4 months ago
The Final One (for Now) Is Done, Just Need To Bluetooth It And Test It Out.

The final one (for now) is done, just need to Bluetooth it and test it out.


Tags
4 months ago
After Filing The 3D Printed Buttons Down And Removing The Other Shelf, The Pressure On The Power And

After filing the 3D printed buttons down and removing the other shelf, the pressure on the power and reset buttons was relieved enough to tighten the screws and finish assembly. This one is ready to be Bluetoothed to a phone.


Tags
4 months ago
Everything Packed In But Still Getting Too Much Pressure Against The Reset Button, So That Will Need

Everything packed in but still getting too much pressure against the reset button, so that will need elevated before I can tighten the housing down


Tags
4 months ago
I Removed The Other Shelf Thinking That It Would Relieve The Pressure On The Power And Reset Buttons,

I removed the other shelf thinking that it would relieve the pressure on the power and reset buttons, but this turned out to be wrong.


Tags
4 months ago
I've Removed The Bottom Left "shelf" That The Radio Sits Against That Blocks Any Wiring From The Radio

I've removed the bottom left "shelf" that the radio sits against that blocks any wiring from the radio to the GPS. Hopefully, this will fix the issue with the radio not properly sitting in the frame. Keep in mind, if you aren't going to wire a GPS unit to the Heltec V3 then you'll not have to remove the "shelf"


Tags
6 months ago
I Filed It Down! I'm Not An Electronics Guru So It Took Me A Bit To Realize That I Just Need To Manipulate

I filed it down! I'm not an electronics guru so it took me a bit to realize that I just need to manipulate the environment in which the Heltec V3 is going to occupy inside the radio frame. I'm considering using hot glue to help secure the radio in place now that the shelf/lip is gone. We'll see once it's in place, but in the meantime, I need to get a replacement radio.


Tags
6 months ago
The Radio Frames Made By Tony G On Printables.com Truly Are Well Designed And If Anyone Is Thinking About

The radio frames made by Tony G on printables.com truly are well designed and if anyone is thinking about building meshtastic radios I would highly suggest downloading any of his designs that suits your needs.

I would have only one fix for this radio frame though, it's this blasted lip/shelf where the heltec v3 is supposed to sit. The design prohibits the connections for the hot and ground wires to the GNSS radio to sit. Granted, I'm not good at soldering but I was good enough to ruin my radio trying to find a way to get the wires soldered in a way that would work. But I think I have a solution.


Tags
6 months ago
Ruined One Of My Heltec V3's By Soldering And Resoldering The Connections For The Hot And Ground Wires

Ruined one of my Heltec V3's by soldering and resoldering the connections for the hot and ground wires trying to get it to fit into the radio frame.


Tags
7 months ago
As Always, There's An Adhesion Issue, But At Least I Have It Printing Again. I Started Over After Adding
As Always, There's An Adhesion Issue, But At Least I Have It Printing Again. I Started Over After Adding

As always, there's an adhesion issue, but at least I have it printing again. I started over after adding painter's masking tape which appears to be working...for now.


Tags
8 months ago
Layer Separation Using The New Direct Drive. This Is A New Learning Curve And I May Have To Change Some

Layer separation using the new direct drive. This is a new learning curve and I may have to change some settings.


Tags
8 months ago
Installed The New Direct Drive Extruder And Hot End Onto The 3D Printer And Successfully Tested The Extrusion

Installed the new direct drive extruder and hot end onto the 3D printer and successfully tested the extrusion of filament. Now to start a print!


Tags
8 months ago
All Parts Printed And Assembled To Check For Accuracy. Again, There's No License Required For This One.

All parts printed and assembled to check for accuracy. Again, there's no license required for this one. Stay tuned!


Tags
8 months ago

Next two parts of the project. No license required


Tags
8 months ago

Began a little project. No amateur radio license required for this one. Whatever could it be? Hint: 900mhz


Tags
5 years ago

Random  Angry Fish Speed Sculpt- by @tinanewtonart

What should I name this character?

Follow me on twitch https://www.twitch.tv/tinanewtonart

Patreon https://www.patreon.com/tinanewtonart

Tumblr: https://tinanewtonart.tumblr.com

Do you want this 3D model? if so contact me via the ask button at the top of the page. 

image
image
image

Tags
7 years ago

She could see them all gathered in the corner, the cool ones, the ones with 3D printers. Those were the ones she wanted to dance with.


Tags
9 years ago
Scientists Have Made A ‘bioink’ To Print Human Cartilage

Scientists have made a ‘bioink’ to print human cartilage

 futurism.com/9gMbz


Tags
2 weeks ago

I GOT A 3D PRINTER (ITS NOT FULLY PUT TOGETHER YET BUT STIL!!!)

I GOT A 3D PRINTER (ITS NOT FULLY PUT TOGETHER YET BUT STIL!!!)

I CAN NOW 3D PRINT THE YAELOKER MASKS!!

I GOT A 3D PRINTER (ITS NOT FULLY PUT TOGETHER YET BUT STIL!!!)
I GOT A 3D PRINTER (ITS NOT FULLY PUT TOGETHER YET BUT STIL!!!)
I GOT A 3D PRINTER (ITS NOT FULLY PUT TOGETHER YET BUT STIL!!!)
I GOT A 3D PRINTER (ITS NOT FULLY PUT TOGETHER YET BUT STIL!!!)
I GOT A 3D PRINTER (ITS NOT FULLY PUT TOGETHER YET BUT STIL!!!)
I GOT A 3D PRINTER (ITS NOT FULLY PUT TOGETHER YET BUT STIL!!!)
I GOT A 3D PRINTER (ITS NOT FULLY PUT TOGETHER YET BUT STIL!!!)
I GOT A 3D PRINTER (ITS NOT FULLY PUT TOGETHER YET BUT STIL!!!)

@yaelokre HOPE YOU LIKE IT! Excited for whatever Is next , I love it!!!


Tags
Loading...
End of content
No more pages to load
Explore Tumblr Blog
Search Through Tumblr Tags